How to Set up a Bath Tub
How to Set up a Bath Tub
Blog Article
The content down below involving How to Install a Bathtub is seriously remarkable. Read it for your own benefit and figure out what you think about it.
Installing a tub isn't precisely brain surgery, however it does require solid plumbing, woodworking, and also sometimes, tiling skills. Replacing an old tub with a brand-new one is also a moderately challenging job. If the old bathtub is conveniently accessible, the project can move immediately; if you need to open up a wall to eliminate the old bathtub and also position the new tub, the task is a lot harder. In either instance, the task is within a home handyman's skills, although you will need a helper to leave the old bathtub as well as embeded in the brand-new one. Make sure you have actually qualified yourself for the job and are comfortable attempting it. Instead of employing a specialist to take control of a halfway-completed task, it is far better to take into consideration using one prior to you start. Opportunities are you might require a specialist plumber to make tube links.
This post will certainly aid you set up a new tub in your bathroom if you have actually currently purchased a new bathtub and also don't need to change the setup of your previous water system pipelines.
Your tools and also product checklist should consist of the following:
Preparing for the Installation
To start with, the supporting frame supplied with the bath ought to be fitted (if required) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is necessary to see to it that if the faucet includes a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is likewise practical to fit a supporting plate under the faucets system to prevent pressure on the bath tub.
Fit the adaptable tap connectors to the bottom of both faucets utilizing 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make certain you use all of the provided washing machines.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bath ought to currently be ready to be suited its last position.
Removing Old Taps
If you require to change old taps with new ones as a part of your setup, after that the first thing you need to do is disconnect the water supply. After doing so, activate the taps to drain any type of water continuing to be in the system. The procedure of removing the existing taps can be quite troublesome as a result of the limited accessibility that is frequently the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipelines to the taps. Have a cloth ready for the staying water that will certainly originate from the pipes. When the supply pipes have actually been gotten rid of, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single taps from turning during this process. Once the taps have been removed, the holes in the bath/basin will have to be cleaned of any type of old sealing compound.
Before proceeding to fit the new taps, compare the pipeline links on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new faucets to fit.
Mounting the Bath tub
Utilizing the two wood boards under its feet, put the bathtub in the called for setting. The wooden boards are helpful in equally spreading the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto 4 little points.
The next objective is to make sure that the tub is leveled all round. This can be achieved by examining the level as well as adjusting the feet on the bath tub until the level checks out level.
To install faucets, fit the bottom of the furthest adaptable tap port to the ideal supply pipeline by making a compression join; after that do the very same for the other tap.
Activate the supply of water as well as inspect all joints and brand-new pipework for leakages as well as tighten them if required. Fill the bath tub as well as likewise examine the overflow electrical outlet as well as the normal electrical outlet for leakages.
Lastly, fix the bathroom paneling as explained in the producer's instruction manual. Tiling and also sealing around the bath tub ought to wait till the bath tub has been used at the very least once as this will resolve it into its last setting.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic connector to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end supplies a connection to the current supply pipelines.
If you need to fit a monobloc, then you will call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, place the faucet in the installing opening in the bath/basin making sure that the washers remain in place in between the faucet as well as the sink. Secure the tap in position with the maker offered backnut. Once the faucet is securely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular faucet connectors. The previous kind ought to be connected to the tap finishes initially, tightening only by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the area where the bathroom satisfies the tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move enough to crack an inflexible seal, triggering the water to penetrate the wall surface between the bathroom as well as the tiling, leading to issues with dampness and also possible leakages to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your fixtures and installations. They are offered in tubes and also cartridges, as well as can sealing voids as much as a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always fill up the tub with water before securing, to allow for the movement experienced when the tub remains in usage. The sealant can split fairly very early if you do not take into account this motion prior to sealing.
Additionally, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise easily offered on the marketplace. It is a good idea to fit the floor tiles making use of waterproof or waterproof adhesive and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I stumbled upon that blog entry on Tools You Need to Install a New Bathtub when looking around the search engines. Sharing is nice. Helping people is fun. Many thanks for your time spent reading it.
Schedule Service
Report this page